Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
Just how do you feel on the subject of How to Install a Bathtub?

Setting up a tub isn't precisely rocket science, but it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a new one is also a moderately hard job. If the old tub is readily accessible, the task can relocate easily; if you need to open a wall surface to remove the old tub as well as position the new tub, the task is a lot harder. In either case, the project is within a house handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the job and are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This article will certainly help you mount a new tub in your washroom if you have actually already acquired a brand-new bathtub and do not need to change the setup of your previous water system pipelines.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in location between the faucet and the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the bath tub up until the spirit level reads level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leaks and tighten them if needed. Load the tub and also inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has actually been used at least once as this will certainly settle it right into its last position.
Preparing for the Installation
To start with, the supporting structure provided with the bathroom must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to complications with dampness and feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I am just very eager about Tools You Need to Install a New Bathtub and I am hoping you enjoyed reading my page. Do you know another person who is excited by the niche? Be sure promote it. Thanks for taking the time to read it.
Urgent plumbing needs? Seek professionals. Report this page